Table of Contents
There are a number of modes of operation the motor can be set to.
- CML mode - this is the standard and default mode.
- Profile mode - run position or speed profiles.
- Torque mode - run the motor by adjusting the torque and maximum speed values.
Setting Mode Of Operation
The control registers in the mode selected use either standard CML registers or registers set directly such as through Modbus-TCP. The mode of operation selected indicates where the control registers will be received
The following table lists the mode of operation and the associated registers
Mode of Operation | Value | Description |
---|---|---|
CML Mode | 0 | Standard CML mode. No control registers associated |
Profile Mode | 2 | Profile mode using P1, S1, A1, A2, R1 and N1 |
3 | Profile mode using Modbus control registers (see registers starting 41029). | |
Torque Mode | 10 | Torque mode using N1, S1 and R1 |
11 | Torque mode using Modbus control registers (see registers starting 41029). |
- Bit0 of the mode of operation selects the register source. I.e. P1 to N1 or the Modbus contorl registers.
Set the mode of operation by the following
- Send "_mop=x" on the CML port when x is the value of the mode of operation
- Assign a variable to "mop" and write the variable in a logic bank. E.g. V0="mop".
- Set modbus register 41041 to the value of the required mode of operation.
Registers
The following registers are used in the different modes of operation. They are NOT use on CML mode.
Controlword
The Controlword is used to control the motor. The usage does depend on the mode that is selected. See the mode for bit usage. B4-B7 are common to all modes.
BIT | Name | Value | Description |
---|---|---|---|
B0 | Operation mode specific | ||
B1 | Operation mode specific | ||
B2 | Operation mode specific | ||
B3 | Operation mode specific | ||
B4 | Disable | 0 1 1 → 0 | Enable the motor Disable the motor Reset any error |
B5 | Reset Error | 0 → 1 | Reset any error |
B6 | Set to Zero | 0 → 1 | Set the current position to 0 |
B7 | Home | 0 → 1 | Start a home search(1) |
(1) Set the home search parameters with K parameters K42-K48
TargetPosition
The TargetPosition sets a new target position for the motor.
Register Name | CML Register | Modbus Register | Unit | Range |
---|---|---|---|---|
TargetPosition | P1 | 41029 | pulses (counts) | -2^31 to +2^31 |
The motor has a maximum resolution of 50,000 counts per revolution. Regardless of the resolution defined in K37 the motor internally will convert the target position to a position based on 50,000. As such the maximum range depends on the motor resolution. For example if K37=3 and the resolution is 1000 pulses/revolution, the maximum target position is 2^31 ÷ (50,000/1,000) = 2^31 ÷ 50 = 42,949,672.
TargetSpeed
The TargetSpeed sets a new maximum speed.
Register Name | CML Register | Modbus Register | Unit | Range |
---|---|---|---|---|
TargetSpeed | S1 | 41031 | pulses/second 10 pulses/second 100 pulses/second | -2^31 to +2^31 |
The unit depends on the motor resolution (K37) value selected. See K37 for more details.
TargetTorque
The TargetTorque sets the maximum torque used by the motor.
Register Name | CML Register | Modbus Register | Unit | Range |
---|---|---|---|---|
TargetTorque | N1 | 41033 | 0.1% rated torque | 0 - 1100 |
The torque is set in a percentage of rated torque. The Cool Muscle will only use the torque required so typically this value should be set to 1100 unless the application requires that the torque is limited.
TargetAcceleration
TargetDeceleration
CML Mode
CML mode is the standard mode that the Cool Muscle motor typically operates in. There are no specific control registers. See the CM1 documentation for CML mode usage.
Profile Mode
Profile mode would be a typical mode used in point-to-point motion and/or continuous velocity motion. The following registers are used depending on the profile mode selected.
Register Name | Profile Mode = 2 (CML Registers) | Profile Mode = 3 (Modbus Registers) | Unit | Description |
---|---|---|---|---|
TargetPosition | P1 | 41029 | pulses (counts) | Next target position the motor will move to |
TargetSpeed | S1 | 41031 | pulses/second | The maximum speed of the profile trajectory |
TargetTorque | N1 | 41033 | 0.1% rated torque | The maximum torque the motor will use |
TargetAcceleration | A1 | 41035 | Kpulses/second2 | Acceleration used when accelerating to TargetSpeed |
TargetDeceleration | A2 | 41037 | Kpulses/second2 | Deceleration used when decelerating to TargetPosition |
Controlword | R1 | 41039 | N/A | Bits in the Controlword dictate profile execution |